SENSKY BS010WL DC 12v to 24v Mini Pir Motion Sensor Switch Occupancy Sensor Switch for DIY LED Lighting (Light Sensor, Delay Time, Sensor Distance, Adjustable)
$9.99
Related Products
Product description
PIR(Passive infrared) Motion sensor is pyroelectric device can detect human movement by detecting Infrared ray emitted by human body.
Automatic Induction: When people enter into the range of induction, it will output a voltage equal to input voltage, after the delay time, it will output 0V; during the delay time if motion detected, the delay time will reset, and start a new delay time. widely used on the Motion-activated lighting, LED strips Security System, automatic sensory device and more.
Specifications :
Operating voltage: DC 12V-30V
Load current: 3A
Detecting range: About 110 degrees cone angle
Trigger way: continuous triggering
Blockade time: 0 seconds
Size: 48*25*14 mm
Attention:
1.Don’t exposed to direct sun light or lighting, big wind, near a heater or air condition.
2.Don’t fix it at a place where there are obstructing material (e.g. Glass, dense clothes) which IR cannot get though.
3.Don’t fix it in strong shock or vibration environment.
4.The PIR Sensor requires a ‘warm-up’ time in order to function properly, about 10s to1min,depend on the delay time; during this time, the signal triggered by the module is not stable, after one minute, it will be ready.
Add to Cart
Add to Cart
Add to Cart
Add to Cart
Customer Reviews
4.4 out of 5 stars 1,345
4.3 out of 5 stars 591
4.3 out of 5 stars 540
4.3 out of 5 stars 591
Price
$9.99$9.99 $9.99$9.99 $9.99$9.99 $9.99$9.99
Model Number
BS010L BS010 BS010WL BS010W
Delay Time
5-25sec (2~280 Seconds adjustable) 5-25sec (2~280 Seconds adjustable) 5-25sec (2~280 Seconds adjustable) 5-25sec (2~280 Seconds adjustable)
Detection Range
4M-7M (10cm-7M adjustable) 4M-7M (10cm-7M adjustable) 4M-7M (10cm-7M adjustable) 4M-7M (10cm-7M adjustable)
Light Sensor
20lux (10~300Lux adjustable) No Light Sensor 20lux (10~300Lux adjustable) No Light Sensor
Voltage
DC 12V-30V DC 12V-30V DC 12V-30V DC 12V-30V
Load current
≤ 3A ≤ 3A ≤ 3A ≤ 3A
【Motion Activated】 : Sensor function triggered by motion, you can use this small motion sensor switch to control lighting like Led strip lighting.
【Light Sensor Adjustable】: This function allows you to use the motion sensor in different ambient condition, for example, you set the light sensor value to 20 lux, when the room ambient light value is above 20 lux, the light won’t turn on, but when room ambient light value is less than 20 lux, the sensor can turn light on when motion detected within sensing range.
【Delay Time Adjustable- Please set this to its minimum value first then try to figure out your values for the Sensitivity and Light Sensor- this will save your time】: The delay time controls how long the light stays on once it gets triggered, during the delay time if motion detected, the delay time will reset and start a new delay time.
【Sensitivity Adjustable】: The sensitivity controls how close you need to be to the sensor in order to activate it.
【Wide Application】: You can use this sensor in different occasions like entryway lighting, cabinet lighting,lighting, pantry lighting, under the bed rails lighting.
11 reviews for SENSKY BS010WL DC 12v to 24v Mini Pir Motion Sensor Switch Occupancy Sensor Switch for DIY LED Lighting (Light Sensor, Delay Time, Sensor Distance, Adjustable)
Add a review
$9.99
Jack S. –
Excellent little sensor with only one caveat.
I bought this to control led strip lights in a small closet, and I bought this one with the light sensor thinking that it was the version that you can turn the light sensor off, but I was mistaken. The closet is small enough so that when you walk in, the sensor detects you and turns on the light, but then it detected the light and shut off; then it realizes it’s dark and turns on the light and shuts off again. I was about to return it when I realized that the entire circuit board slides right out. Under the translucent dome are two sensors; the center, square sensor detects motion, the round sensor on the side with the wavy line is the photoreceptor. I covered the photoreceptor with a tiny square of electrical tape and now it works perfectly. Please note: this is not a defect in the device, merely a side effect of having lights and a light sensitive sensor in a 2′ x 5′ space. The motion sensor works very well, the delay is adjustable, and I intend to buy more. Also, the delay on mine was set to minimum which also caused the light to flicker off and on but adjusting it even slightly more positive fixes that problem. It is a completely silent device, which was important to me, as the motion sensor switche we have in the master closet has an audible click when it activates the light (that one is a $29 Lutron Decora). Another note, it’s much smaller than I thought it would be which is a huge plus!One last note: I’m using it with the Pautix LED strip that comes with its own remote that dims the strip; if you dim the strip to your liking and walk away, the LED strip remembers the last setting so you don’t have to adjust it every time. I couldn’t be happier with this setup over something like a WiFi hub installed product.
Michael –
Good buy, can be very sensitive at a good distance.
Used this for under the cabinet lighting, and wanted it to turn on when someone came in. Works really good. It was picking up movement across the kitchen. Adjustments were finicky but was able to bring it down. Over all, good buy.
Ron P. –
Perfect for any small room
Seems tricky to adjust, but it’s actually pretty easy! Works great for my garage bathroom light!
bob dobbs –
Easy to install and work reliably. Used them with a relay to control incandescent lights
This item solved a problem I had lighting a long, outdoor walkway on the side of my house. I needed an easy way to illuminate the path for people coming from either direction. The problem was that most motion lights could not monitor both sides of this walkway easily, or if they could, they would only control a spot light which was too harsh for my installation. I could have also used high-voltage motion sensors and wired them to an outlet, but then I would have had to install conduit. By using low voltage I was able to install them using small wires and zip ties without needing conduit.This replaced a couple of Insteon SmartHome motion sensors that broke over time. Since the company has since gone out of business I found that I had to DIY if I wanted to control the existing lights in a similar way. Using these, I was able to replicate the function of the Insteon motion sensors.I hooked two of these in parallel to a 12volt relay that was wired to an independent outlet in which I plugged incandescent rope lights. The lights were run the length of the walkway. Since there is one of these motion sensors on either side of this path, a person could approach from either direction and the rope lights will turn on (and anything else plugged into that ‘controlled’ outlet). I could have just used 12v LED lights and not needed the relay, but I already had the lights installed and wanted the flexibility to change them later on.
AlkiBeach –
– The Smartest Sub $10 Nightlight I’ve Ever Owned!!!!
Love it.In the box is a diagram that shows what each set-screw/rheostat does:You can control-How long it stays onAt what brightness it will come on at WHEN it detects motion.It Detects motion, set-screw to set the sensitivity of the motion sensor.Now, I did have to buy a LED dimmer dial thingy – because without it, the strip light was basically auditioning for a Playboy Bunny Bar. With the dimmer, it’s perfect—soft glow, no interrogation vibes.Middle of the day? No light. After sunset? Boom—low glow. Installed it as a base‑cabinet LED strip nightlight in the bathroom. And now, when I stumble into the bathroom at 2 a.m., it politely flicks on dim, waits 30 seconds, then shuts off like it’s saying:“Alright buddy, you’ve done your business, back to bed.”
A. Cerqua –
Good product and Value!
This motion worked out very nicely for me. I was looking for a way to light my gun safe. On YouTube I found a number of videos using LED lights to do this. One of them referenced this sensor as part of what they used along with the LED lights and power supply. I inserted the product link for them in this review so I hope they show up. It could not have been easier to do. Took me about a half hour. The results were excellent! There are three screws inside this unit to make adjustments. The information on the package is very brief and to me it was confusing. I started out by just setting them all in the middle and it was perfect! Several days after I received the item (and had installed it) I received with nice detailed instructions on the setting screws. I should have gotten it the day it shipped I suppose but it is helpful so if you are confused about anything just wait for the e-mail. If you’re doing a gun safe check out YouTube. Otherwise a big thumbs up!inShareplus 12V LED Strip Power Supply 2A 24W, Wall Mounted 12V Switching Power Supply, 110V to 12 Power Supply for LED Strip Light with 5.5/2.1 DC Female Barrel Connector to Screw AdapterLE 16.4ft LED Flexible Light Strip, 300 Units SMD 2835 LEDs, 12V DC Non-waterproof, Light Strips, LED ribbon, DIY Christmas Holiday Home Kitchen Car Bar Indoor Party Decoration (Daylight White)
Capital C –
I used these to turn a set of Govee LED strip lights into the perfect automatic closet illumination! I love the fact the sensitivity and duration can easily be adjusted.
billfern –
I like to turn off my desk light when away, but often I am up late at night or early morning when it is dark so having a sensor switch that detects me when I am wandering around is a good idea. Good safety idea to see where you are going. so on comes the desk lamp, and it is safe.
Darlene Baddeley –
This has been fantastic. I walk into the room and my LED lights automatically turn on. Great upgrade for LED lights and well priced.
D. Davis –
I bought some of these do use to activate a custom LED strip within lower cabinets with a long lazy Suzan / pull out. I have only implemented one so far. While it does take some experimentation to set the on time, so far it has been working very well.
Louis du Québec –
Ouvre et ferme les dels de notre garde-robe d’entrée, super petit gadget